The feature packed Arduino® NanoRP2040 Connect brings the new Raspberry Pi RP2040 microcontroller to the Nano form factor. Make the most of the dual core 32-bit Arm® Cortex®-M0+ to make Internet of Things projects with Bluetooth and WiFi connectivity thanks to the U-blox® Nina W102 module. Dive into real-world projects with the onboard accelerometer, gyroscope, RGB LED and microphone. The Arduino®Nano RP2040 Connect is pin-compatible with the Nano form factor to develop robust solutions with minimal effort!
Specifications:
- Raspberry Pi RP2040 Micrcontroller:
- 133MHz 32bit Dual Core Arm® Cortex®-M0+
- 264kB on-chip SRAM
- Direct Memory Access (DMA) controller
- Support for up to 16MB of off-chip Flash memory via dedicated QSPI bus
- USB 1.1 controller and PHY, with host and device support
- 8 PIO state machines
- Programmable IO (PIO) for extended peripheral support
- 4 channel ADC with internal temperature sensor, 0.5 MSa/s, 12-bit conversion
- SWD Debugging
- 2 on-chip PLLs to generate USB and core clock
- 40nm process node
- Multiple low power mode support
- USB 1.1 Host/Device
- Internal Voltage Regulator to supply the core voltage
- Advanced High-performance Bus (AHB)/Advanced Peripheral Bus (APB)
- U-blox® Nina W102 WiFi/Bluetooth Module:
- 240MHz 32bit Dual Core Xtensa LX6
- 520kB on-chip SRAM
- 448 Kbyte ROM for booting and core functions
- 16 Mbit FLASH for code storage including hardware encryption to protect programsand data
- 1 kbit EFUSE (non- erasable memory) for MAC addresses, module configuration,Flash-Encryption, and Chip-ID
- IEEE 802.11b/g/n single-band 2.4 GHz WiFi operation
- Bluetooth 4.2
- Integated Planar Inverted-F Antenna (PIFA)
- 4x 12-bit ADC
- 3x I2C, SDIO, CAN, QSPI
- Memory:
- AT25SF128A 16MB NOR Flash
- QSPI data transfer rate up to 532Mbps
- 100K program/erase cycles
- ST LSM6DSOXTR 6-axis IMU:
- 3D Gyroscope: ±2/±4/±8/±16 g full scale
- 3D Accelerometer: ±125/±250/±500/±1000/±2000 dps full scale
- Advanced pedometer, step detector and step counter
- Significant Motion Detection, Tilt detection
- Standard interrupts: free-fall, wakeup, 6D/4D orientation, click and double-click
- Programmable finite state machine: accelerometer, gyroscope and external sensors
- Machine Learning Core
- Embedded temperature sensor
- ST MP34DT06JTR MEMS Microphone:
- AOP = 122.5 dBSPL
- 64 dB signal-to-noise ratio
- Omnidirectional sensitivity
- -26 dBFS ± 1 dB sensitivity
- RGB LED:
- Common Anode
- Connected to U-blox® Nina W102 GPIO
- Microchip® ATECC608A Crypto:
- Cryptographic Co-Processor with Secure Hardware-Based Key Storage
- I2C, SWI
- Hardware Support for Symmetric Algorithms:
- SHA-256 & HMAC Hash including off-chip context save/restore
- AES-128: Encrypt/Decrypt, Galois Field Multiply for GCM
- Internal High-Quality NIST SP 800-90A/B/C Random Number Generator (RNG)
- Secure Boot Support:
- Full ECDSA code signature validation, optional stored digest/signature
- Optional communication key disablement prior to secure boot
- Encryption/Authentication for messages to prevent on-board attacks
- I/O:
- 14x Digital Pin
- 8x Analog Pin
- Micro USB
- UART, SPI, I2C Support
- Power supply:
- From VIN: 5Vdc (4...22Vdc)
- From USB connector: 5Vdc (4,75...5,25Vdc)
- Safety Information: Class A
|